What this Picture Mat Size Calculator does
The Picture Mat Size Calculator estimates the total face area of a mat from the width and height of the artwork and the width of the border. It assumes the border has the same width on all four sides. The result is expressed in square inches and can help with early layout planning for a framed print, drawing, photograph, or other flat artwork.
To calculate the outer dimensions, the tool adds twice the border width to each artwork dimension. It then multiplies those outer dimensions to find the mat face area. For example, an 8 by 10 inch image with a 2 inch border has an estimated outer size of 12 by 14 inches. Its face area is 168 square inches.
The result describes a rectangular mat face. It does not determine the exact cut opening, frame size, or amount of material a shop should order. Mat openings are often made slightly smaller than the artwork so the edge is held in place. The amount of overlap depends on the artwork, mounting approach, and framing plan.
How to use the Picture Mat Size Calculator
- Measure the artwork. Enter its width and height in inches. Measure the actual piece that will sit behind the mat, rather than relying on a nominal print size if its edges differ.
- Choose a border width. Enter the border width for one side. The calculator applies that amount to both the left and right, and to both the top and bottom.
- Read the area estimate. The result is the area within the mat's outside rectangle, before subtracting the opening.
For a worked example, use artwork that is 8 inches wide and 10 inches tall, with a 2 inch border. The formula is (artwork width + 2 × border) × (artwork height + 2 × border). Substituting the measurements gives (8 + 2 × 2) × (10 + 2 × 2), or 12 × 14, which equals 168 square inches. The estimated outside dimensions are 12 by 14 inches.
Enter fractional measurements when needed. For instance, a border may be 1.5 inches on each side. Keep the units consistent throughout. This calculator accepts inches, so convert any measurements taken in centimeters before entering them.
How the Picture Mat Size Calculator formula works
The calculation has two steps. First, it adds two border widths to each artwork dimension because there is one border on each opposing side. Then it multiplies the resulting outside width by the outside height.
Outside width = artwork width + (2 × border width)
Outside height = artwork height + (2 × border width)
Mat face area = outside width × outside height
With artwork measuring 8 by 10 inches and a 2 inch border, the outside width is 8 + 4 = 12 inches. The outside height is 10 + 4 = 14 inches. Multiplication gives an area of 168 square inches. The formula does not subtract the artwork opening. It reports the full rectangular face bounded by the mat's outside edges.
Area alone does not specify shape. A 12 by 14 inch mat and a 10 by 16.8 inch mat both have an area of 168 square inches, but their proportions differ. The dimensions you enter determine the proportions of this calculator's estimate.
Use cases for the Picture Mat Size Calculator
This estimate is useful during the early stages of visual planning, when you are comparing border widths or checking how much the mat changes the artwork's overall footprint. It can also help organize measurements before discussing a project with a framing professional.
- Compare border options. Try several widths to see how the outside dimensions change around the same artwork.
- Plan a display layout. Use the estimated outer dimensions to sketch spacing between framed pieces on a wall or arrange a group of works on a page.
- Check proportions. See whether a proposed border makes the finished rectangle feel wider or taller relative to the image.
- Prepare a measurement note. Record the artwork dimensions and preferred border width before requesting a precise cut or frame quote.
For example, increasing a border from 2 inches to 3 inches around an 8 by 10 inch image changes the estimated outside dimensions from 12 by 14 inches to 14 by 16 inches. The face area becomes 224 square inches. That change can be helpful to visualize, though the best-looking arrangement depends on the artwork and its intended presentation.
Other factors to consider when calculating mat size
The calculator assumes a centered opening and equal borders. Some designs use a wider bottom border, an off-center opening, multiple openings, or a decorative shape. In those cases, the outside rectangle may still be useful, but it does not describe the full layout.
Also consider these practical details before cutting or ordering materials:
- Opening overlap. The visible opening may be smaller than the artwork so the mat covers a narrow edge. Confirm the intended overlap with the person cutting the mat.
- Frame clearance. A frame may cover part of the mat's outer edge. Confirm the frame's usable opening and how the mat will sit inside it.
- Measurement precision. Measure width and height at more than one point if the artwork or paper is not perfectly square. Use the measurements that the framing plan requires.
- Material and design. Mat thickness, bevels, backing, and layered mats can affect fabrication choices even when the face dimensions are unchanged.
For an exact cut, provide the artwork size, desired visible opening, mat outside size, and any uneven border requirements to the framer or cutting service. The area estimate is a planning aid and does not replace those specifications.
Frequently asked questions
Does the result show the mat's outside dimensions?
The result shows area, while the outside width and height can be found by adding twice the border width to each artwork dimension. For an 8 by 10 inch image with a 2 inch border, those dimensions are 12 by 14 inches.
Is the mat border width entered for one side or both sides?
Enter the width for one side. The formula doubles it to account for the two horizontal borders and the two vertical borders.
Does the estimate include the opening?
No. It calculates the full outside rectangular face area and does not subtract the central opening. Opening size and overlap should be planned separately.
Can I use centimeters?
The inputs are in inches. Convert both artwork measurements and the border width to inches before calculating so the dimensions use one consistent unit.
Can I use this number to order mat board?
Use it as an initial face-area estimate. A cutting layout may require additional material, and the opening, margins, frame coverage, and cutting method affect the final specification. Confirm the order dimensions with the framing provider.